|
Sintered Titanium and Porous Titanium Foam Sheet, 30 µm Filtration Rating, 200 × 200 × 1.5 mm, 20 PPI, 1 Piece
Research-grade laboratory product
|
|||||||||||||||||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||||||||||||||||
|
LABORATORY PROCUREMENT SUPPORT
For filtration accuracy, dimensional confirmation, material compatibility or custom configuration review, contact our technical sales team.
E-MAIL: inquiry@atomfair.com
|
|||||||||||||||||||||||||||||||||||||||||||||||
|
Manufacturer: Atomfair LLC
Brand: ATOMFAIR®
|
This sheet requires careful handling to avoid crushing and contamination of its porous structure. Operating temperature must not exceed 300°C, and media compatibility must be verified before use.
- Service Temperature Limit: The recommended service temperature is ≤300°C to prevent material degradation.
- Surface Protection: Protect the porous surface from crushing and contamination during handling, cleaning, and installation.
- Cleaning Methods: The sheet can be cleaned using backflushing, steam, ultrasonic, or chemical methods compatible with the process medium.
- Media Compatibility: Media compatibility, operating pressure, and temperature must be reviewed before installation.
- Machining Capability: The sheet can be cut, welded, or machined for assembly integration, but care must be taken to avoid damaging the porous structure.
Proper handling and installation are essential to maintain the integrity of the porous titanium sheet. Follow these steps to ensure safe integration into filtration assemblies.
Required Equipment: Ultrasonic cleaner, Steam cleaner, Backflushing system, Filtration assembly
- Inspect
Inspect the sheet for any visible damage or contamination before use. - Clean
Clean the sheet using an appropriate method such as backflushing, steam, ultrasonic, or chemical cleaning. - Install
Install the sheet into the filtration assembly ensuring proper sealing and alignment. - Verify
Verify that the operating temperature does not exceed the recommended 300°C limit.
How does the 20 PPI pore density relate to the 30 μm filtration rating in this sintered titanium foam sheet?
The 20 PPI (pores per inch) and 30 μm filtration rating describe independent characteristics. PPI defines the cellular structure with approximately 1.27 mm cell spacing, while the filtration rating specifies the particle retention size. The 35–45% porosity and interconnected through-pore structure enable flow, but filtration precision is governed by the pore size distribution, not the cell spacing. The sheet's 30 μm rating means it retains particles ≥30 μm while allowing fluid passage through the open titanium framework.
What compatibility and integration constraints should be evaluated before using this 200 × 200 × 1.5 mm titanium foam sheet in a chemical filtration assembly?
Media compatibility with titanium must be confirmed for the specific process fluid, as titanium offers corrosion resistance in many but not all environments (e.g., strong reducing acids). The recommended service temperature is ≤300°C. The sheet can be cut, welded, and machined for integration, but care must be taken to avoid crushing the porous surface. The air permeability of 5 × 10⁻⁴ L/(cm²·min·Pa) and 35–45% porosity influence pressure drop and flow rate, requiring verification against target operating conditions before installation.
What cleaning methods are specified for maintaining the 30 μm filtration performance of this sintered titanium foam sheet?
The product supports backflushing, steam cleaning, ultrasonic cleaning, and compatible chemical cleaning procedures. The metallic construction allows repeated cleaning without degradation, provided the porous surface is protected from crushing and contamination. Appropriate cleaning method selection depends on the process medium and operating procedure, as listed in the handling and cleaning notes.
The AF-T20-C1530 sintered titanium foam sheet provides 30 µm filtration in a 20 PPI, 200 × 200 × 1.5 mm format with 35–45% interconnected porosity, but its service envelope is bounded by a ≤300°C recommended temperature and required media/process compatibility review before installation.
Positive
- Interconnected porous filtration structure: The 30 µm filtration rating, 20 PPI cellular structure, and 35–45% interconnected porosity provide stable separation with open flow paths for solid-liquid, gas-solid, and gas-liquid duties.
- Corrosion-resistant machinable titanium construction: The sintered titanium or titanium-alloy structure offers corrosion resistance and thermal stability in compatible media, while the metallic body supports cutting, welding, and basic machining for assembly integration.
Trade-offs
- Service temperature limited to 300°C: Recommended service temperature is ≤300°C, so higher-temperature process streams would require alternate media or explicit design validation beyond this product's stated limits.
- Porous surface requires handling protection: The porous surface must be protected from crushing and contamination, and cleaning via backflushing, steam, ultrasonic, or chemical routes must be matched to the process medium and operating procedure.
Every advanced material, component, equipment, and instrument in our catalog is backed by rigorous testing. We maintain strict internal quality management frameworks and align with CE conformity metrics to deliver transparent, reproducible performance data via our public open-science repository.
To request raw batch performance data, submit formal vendor registration paperwork, or execute a fast-turnaround R&D manufacturing loop, contact us at inquiry@atomfair.com.
Item is dispatched under the Atomfair Shipping & Delivery Framework (Free worldwide shipping on orders over $59 USD excl. heavy equipment). Return is governed by the Atomfair Return & Refund Policy (7-day technical return window).
