|
Sintered Titanium and Porous Titanium Foam Sheet, 10 µm Filtration Rating, 120 × 120 × 10 mm, 80 PPI, 1 Piece
Research-grade laboratory product
|
|||||||||||||||||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||||||||||||||||
|
LABORATORY PROCUREMENT SUPPORT
For filtration accuracy, dimensional confirmation, material compatibility or custom configuration review, contact our technical sales team.
E-MAIL: inquiry@atomfair.com
|
|||||||||||||||||||||||||||||||||||||||||||||||
|
Manufacturer: Atomfair LLC
Brand: ATOMFAIR®
|
The sheet must be protected from surface crushing and contamination to preserve its porous structure and filtration integrity. Media compatibility, operating pressure, temperature, and target flow must be reviewed before installation to avoid material degradation or process failure.
- Temperature Limit: Recommended service temperature does not exceed 300°C to prevent structural compromise.
- Cleaning Compatibility: Cleaning methods include backflushing, steam, ultrasonic, and compatible chemical procedures depending on the process medium.
- Mechanical Integrity: The metallic construction supports cutting, welding, and basic machining but requires care to avoid pore collapse during assembly.
Inspect the sheet for visible damage or contamination before installation to ensure filtration integrity. Confirm media compatibility, operating pressure, and temperature against the sheet's rated limits prior to use.
Required Equipment: Clean gloves, Soft brush or lint-free cloth
- Inspect the sheet
Inspect the porous surface for crushing, dents, or contamination before handling. - Clean the sheet
Clean the sheet using backflushing, steam, ultrasonic, or a compatible chemical method appropriate for the process medium. - Install the sheet
Install the sheet into the filtration assembly, ensuring the sealing surfaces are clean and the sheet is not over-compressed. - Verify operating conditions
Verify that the operating temperature remains at or below 300°C and that the media is compatible with titanium.
How does the 80 PPI pore density of the Atomfair sintered titanium foam sheet relate to its 10 µm filtration rating and flow permeability?
The 80 PPI structure provides approximately 0.32 mm cell spacing and 35–45% porosity, giving a relative air permeability of 5×10^−5 L/(cm²·min·Pa). This cellular geometry supports the 10 µm filtration precision while maintaining open interconnected flow paths, but actual flow performance depends on the specific process conditions.
Can the Atomfair 10 µm titanium foam sheet be welded or machined for custom assembly integration?
Yes, the metallic construction supports cutting, welding, and basic machining for assembly integration, as stated in the product specifications. The sheet is made from titanium or titanium-alloy powder via high-vacuum sintering, and its porous structure can be handled similarly to dense titanium if care is taken to avoid crushing the pores.
What cleaning methods are compatible with the Atomfair 80 PPI titanium foam sheet to maintain its 10 µm filtration performance?
Compatible cleaning methods include backflushing, steam cleaning, ultrasonic cleaning, and chemical cleaning procedures, as specified in the product handling notes. The porous surface should be protected from crushing and contamination during cleaning to preserve the 0.32 mm cell spacing and interconnected flow paths.
This 120 × 120 × 10 mm sintered titanium foam sheet delivers a 10 µm filtration rating in an 80 PPI interconnected porous structure with 35–45% porosity and approximately 0.32 mm cell spacing, supporting liquid/gas separation, catalyst recovery, and flow-distribution R&D with low flow resistance. Its corrosion-resistant titanium framework is cleanable and reusable, but the 300°C service ceiling and required media-compatibility and surface-protection checks constrain installation choices.
Positive
- 10 µm filtration with 80 PPI open-cell structure: The 120 × 120 × 10 mm sheet provides a 10 µm filtration rating in an 80 PPI interconnected titanium framework with 35–45% porosity and ~0.32 mm cell spacing, supporting solid-liquid, gas-solid, and gas-liquid separation with low flow resistance.
- Corrosion-resistant, cleanable metallic porous medium: The titanium-based sintered structure offers corrosion resistance and thermal stability in compatible media, and the metallic sheet can be cleaned by backflushing, steam, ultrasonic, or compatible chemical procedures for reuse.
Trade-offs
- Service-temperature ceiling of 300°C: Recommended service temperature is ≤300°C, so higher-temperature process streams or thermal exposure beyond this limit require validation before installation.
- Surface and media compatibility constraints: The porous surface must be protected from crushing and contamination, and media compatibility, operating pressure, temperature, target flow, and dimensional tolerance must be reviewed before use because corrosion resistance is limited to compatible process conditions.
Every advanced material, component, equipment, and instrument in our catalog is backed by rigorous testing. We maintain strict internal quality management frameworks and align with CE conformity metrics to deliver transparent, reproducible performance data via our public open-science repository.
To request raw batch performance data, submit formal vendor registration paperwork, or execute a fast-turnaround R&D manufacturing loop, contact us at inquiry@atomfair.com.
Item is dispatched under the Atomfair Shipping & Delivery Framework (Free worldwide shipping on orders over $59 USD excl. heavy equipment). Return is governed by the Atomfair Return & Refund Policy (7-day technical return window).
