|
Sintered Titanium and Porous Titanium Foam Sheet, 50 µm Filtration Rating, 160 × 160 × 10 mm, 80 PPI, 1 Piece
Research-grade laboratory product
|
|||||||||||||||||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||||||||||||||||
|
LABORATORY PROCUREMENT SUPPORT
For filtration accuracy, dimensional confirmation, material compatibility or custom configuration review, contact our technical sales team.
E-MAIL: inquiry@atomfair.com
|
|||||||||||||||||||||||||||||||||||||||||||||||
|
Manufacturer: Atomfair LLC
Brand: ATOMFAIR®
|
The porous titanium structure is susceptible to crushing and contamination if the surface is not protected during handling and storage. Media compatibility, operating pressure, temperature, and target flow must be reviewed before installation to prevent structural degradation or process failure.
- Surface Protection Requirement: Protect the porous surface from crushing and contamination during handling and storage.
- Service Temperature Limit: Recommended service temperature does not exceed 300°C to maintain structural integrity.
- Media Compatibility Review: Confirm media compatibility before installation to avoid corrosion or chemical attack in incompatible process fluids.
Proper handling and cleaning preserve the porous structure and filtration performance of the titanium foam sheet. Cleaning methods include backflushing, steam, ultrasonic, or compatible chemical procedures depending on the process medium.
Required Equipment: Backflushing system, Steam cleaning equipment, Ultrasonic bath
- Inspect the sheet
Inspect the porous surface for any visible damage or contamination before installation. - Select cleaning method
Select a cleaning method—backflushing, steam, ultrasonic, or chemical—based on the process medium and operating procedure. - Perform cleaning
Perform the chosen cleaning procedure to remove trapped particulates without damaging the porous structure. - Rinse and dry
Rinse the sheet with compatible solvent or deionized water and allow it to dry completely before reuse.
How does the 80 PPI pore density relate to the 50 µm filtration rating, and what does it imply for flow resistance and separation efficiency?
The 80 PPI (pores per inch) indicates a cellular structure with approximately 0.32 mm cell spacing, while the 50 µm filtration rating refers to the particle size retained. The 35–45% porosity and interconnected through-pore structure provide low flow resistance; the relative air permeability is 1 × 10⁻³ L/(cm²·min·Pa). Higher PPI generally increases filtration precision but may reduce permeability, so this balance is suitable for applications requiring moderate filtration with acceptable flow.
What are the maximum operating temperature and material compatibility constraints for this sintered titanium foam sheet?
The recommended service temperature is ≤300°C. The sheet is made from titanium or titanium alloy, offering corrosion resistance in compatible media. However, operating pressure, media compatibility, and target flow must be reviewed before installation. The sheet can be cut, welded, and machined for assembly integration, but the porous surface must be protected from crushing.
What cleaning and maintenance procedures are recommended for this porous titanium sheet to avoid clogging or damage?
Cleaning options include backflushing, steam, ultrasonic, and compatible chemical procedures. The porous surface should be protected from crushing and contamination during handling. Regular cleaning based on the process medium helps maintain filtration performance. The metallic construction supports reuse in compatible conditions.
This 160 × 160 × 10 mm sintered porous titanium sheet combines a 50 µm filtration rating with an 80 PPI cellular structure, approximately 0.32 mm cell spacing, and 35–45% open porosity. Its interconnected metallic framework is suited for laboratory filtration, catalyst recovery, porous-electrode development, and flow-distribution studies within a recommended service temperature of ≤300°C.
Positive
- Interconnected porosity with 50 µm filtration rating: The 35–45% porosity and approximately 0.32 mm cell spacing create interconnected through-pore paths that support stable solid-liquid, gas-solid, and gas-liquid separation at a 50 µm filtration rating with low flow resistance.
- Corrosion-resistant, cleanable metallic construction: The titanium-based porous structure provides corrosion resistance and thermal stability in compatible media, and its metallic construction permits cutting, welding, and basic machining. Backflushing, steam, ultrasonic, or compatible chemical cleaning supports reuse.
Trade-offs
- Service temperature limited to 300°C: Recommended service temperature is ≤300°C, so integration into higher-temperature gas, steam, or thermal-management processes must be verified before installation.
- Porous surface requires handling protection: The porous surface must be protected from crushing and contamination, and the cleaning method must be matched to the process medium and operating procedure to preserve filtration performance.
Every advanced material, component, equipment, and instrument in our catalog is backed by rigorous testing. We maintain strict internal quality management frameworks and align with CE conformity metrics to deliver transparent, reproducible performance data via our public open-science repository.
To request raw batch performance data, submit formal vendor registration paperwork, or execute a fast-turnaround R&D manufacturing loop, contact us at inquiry@atomfair.com.
Item is dispatched under the Atomfair Shipping & Delivery Framework (Free worldwide shipping on orders over $59 USD excl. heavy equipment). Return is governed by the Atomfair Return & Refund Policy (7-day technical return window).
