|
LED Plant Growth Chamber, 160 L, with Humidity Control
Research-grade laboratory product
|
|||||||||||||||||||||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||||||||||||||||||||
|
LABORATORY PROCUREMENT SUPPORT
For model selection, accessory matching, installation-space review, power-supply confirmation or configuration support, contact our technical sales team.
E-MAIL: inquiry@atomfair.com
|
|||||||||||||||||||||||||||||||||||||||||||||||||||
|
Supplier: Atomfair
Brand: ATOMFAIR®
|
This chamber must be operated within a 0–35°C ambient environment and connected to a dedicated AC 220 V 50 Hz power supply rated for 1750 W. Ensure unobstructed air circulation around the unit and keep all service ports, shelves, and doors accessible for routine maintenance.
- Ambient temperature limit: The working environment must remain between 0°C and 35°C to maintain stable chamber performance and compressor longevity.
- Power supply requirement: Connect the chamber exclusively to an AC 220 V 50 Hz outlet that can supply the full 1750 W load without sharing the circuit.
- Ventilation clearance: Air inlets and exhaust paths must not be obstructed to prevent overheating and ensure accurate humidity control.
- Transport orientation: Keep the chamber upright at all times during transport and installation to avoid compressor damage and refrigerant system failure.
- Accessibility for maintenance: Control interfaces, shelves, ports, and door seals must remain accessible for cleaning, calibration, and inspection.
This procedure describes the safe installation and programming of the growth chamber. Follow these steps to prepare the unit for controlled cultivation cycles.
Required Equipment: Suitable lifting equipment (e.g., forklift or pallet jack)
- Position the chamber
Position the chamber upright in an installation space of at least 810 x 780 x 1225 mm with adequate clearance for ventilation and maintenance access. - Connect to power
Connect the chamber to a dedicated AC 220 V 50 Hz power outlet rated for at least 1750 W to ensure stable operation. - Program environmental parameters
Use the 7-inch color touchscreen controller to program the desired temperature, humidity, and lighting cycles via the multi-segment interface. - Verify airflow and service paths
Verify that all air inlets, exhaust paths, shelves, ports, doors, and control interfaces are unobstructed before initiating the chamber.
How does the operating temperature range of the LED Plant Growth Chamber vary between no-light, single-layer light, and double-layer light configurations?
The temperature control range depends on the lighting load: without light, 5 to 45 °C; with single-layer light, 10 to 45 °C; with double-layer light, 15 to 45 °C. This shift occurs because the modular LED lighting adds heat, raising the minimum achievable temperature. The chamber uses dual imported compressors and energy-saving cooling to maintain stability within each band.
Can the humidity control system maintain conditions below 50% RH, and what are the limitations?
The humidity control range is 50%RH to 90%RH with a deviation of ±3%RH at 80%RH. It does not provide dehumidification below 50%RH. For applications requiring lower humidity, optional accessories such as a CO2 inlet or external dehumidification support would be needed, as the chamber is designed for humidification and climate simulation in that band.
What are the critical installation requirements for power, space, and environmental conditions?
The chamber requires a 1750 W power supply at AC 220 V, 50 Hz, and a working environment of 0 to 35 °C. External dimensions are 810 x 780 x 1225 mm. Adequate clearance must be maintained for air inlets, exhaust paths, and access to ports and controls. The unit must be kept upright during transport and set on a stable surface to ensure reliable compressor and sensor operation.
The 160 L LED Plant Growth Chamber with humidity control features a SUS304 stainless steel interior, dual compressors, and programmable control for temperature, humidity, and lighting. Its temperature range is constrained by active lighting, and humidity precision is moderate, making it suitable for standard plant growth and climate simulation but not for protocols requiring low-temperature illumination or tight humidity control.
Positive
- Corrosion-resistant SUS304 chamber interior: The SUS304 stainless steel chamber interior provides chemical resistance and easy cleaning, critical for contamination control in plant growth and tissue culture applications.
- Dual compressors for long-duration stability: The dual imported compressors with long-duration operation design ensure consistent temperature control and reliable performance during extended cultivation or climate simulation experiments.
Trade-offs
- Temperature range constrained by active lighting: The minimum achievable temperature increases from 5°C without light to 10°C with single-layer light, limiting low-temperature applications that require simultaneous illumination.
- Moderate humidity control precision: Humidity deviation of ±3%RH at 80%RH may not meet the requirements of humidity-sensitive protocols such as specific tissue culture or material stability studies.
Every advanced material, component, equipment, and instrument in our catalog is backed by rigorous testing. We maintain strict internal quality management frameworks and align with CE conformity metrics to deliver transparent, reproducible performance data via our public open-science repository.
To request raw batch performance data, submit formal vendor registration paperwork, or execute a fast-turnaround R&D manufacturing loop, contact us at inquiry@atomfair.com.
Item is dispatched under the Atomfair Shipping & Delivery Framework (Free worldwide shipping on orders over $59 USD excl. heavy equipment). Return is governed by the Atomfair Return & Refund Policy (7-day technical return window).
