|
Sintered Titanium and Porous Titanium Foam Sheet, 30 µm Filtration Rating, 160 × 160 × 10 mm, 80 PPI, 1 Piece
Research-grade laboratory product
|
|||||||||||||||||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||||||||||||||||
|
LABORATORY PROCUREMENT SUPPORT
For filtration accuracy, dimensional confirmation, material compatibility or custom configuration review, contact our technical sales team.
E-MAIL: inquiry@atomfair.com
|
|||||||||||||||||||||||||||||||||||||||||||||||
|
Manufacturer: Atomfair LLC
Brand: ATOMFAIR®
|
This porous titanium sheet requires verification of media compatibility, operating pressure, temperature, target flow, and dimensional tolerance before installation. The porous structure must be protected from crushing and contamination, and cleaning methods must be selected based on the process medium.
- Compatibility verification: Confirm that the process fluid or gas is compatible with the titanium or titanium-alloy porous structure under the planned operating conditions.
- Operating limit review: Confirm material grade, operating pressure, temperature, target flow, and dimensional tolerance before installation.
- Porous surface protection: Protect the porous surface from crushing and contamination during handling, storage, and installation.
- Cleaning method selection: Choose backflushing, steam, ultrasonic, or chemical cleaning according to the process medium and operating procedure.
- Assembly matching and integration: Review the cellular structure designation and the micrometre filtration precision together when matching this sheet to an assembly, and perform cutting, welding, or basic machining only when assembly integration requires it.
Prepare the sheet by confirming that the planned process conditions and media are compatible with the titanium or titanium-alloy porous structure. Install the sheet without crushing or contaminating the porous surface, then clean it using a method matched to the process medium.
Required Equipment: Ultrasonic cleaning bath, Steam cleaning system, Backflushing system
- Confirm the sheet is clean
Confirm that the sheet is free of visible contamination before installation. - Verify compatibility
Confirm that the process medium is compatible with the titanium or titanium-alloy porous structure and verify material grade, operating pressure, temperature, target flow, and dimensional tolerance before installation. - Install the sheet
Install the sheet into the assembly while keeping the porous surface protected from crushing and contamination. - Select a cleaning method
Select a cleaning method from backflushing, steam, ultrasonic, or chemical cleaning based on the process medium and operating procedure. - Clean the sheet
Clean the sheet using the selected method according to the process medium and operating procedure.
How does the 80 PPI pore density relate to the 30 µm filtration rating in this sintered titanium foam sheet?
The 80 PPI describes the cellular structure density, while the 30 µm rating specifies filtration precision. The source states that PPI and micrometre values describe different aspects and both should be reviewed together when matching the sheet to an assembly. The 0.32 mm cell spacing and 35–45% porosity provide interconnected flow paths, with a relative air permeability of 5 × 10⁻⁴ L/(cm²·min·Pa). This combination balances mechanical strength and flow resistance.
Can the 160×160×10 mm sintered titanium sheet be cut or welded for custom assembly integration?
Yes, the metallic construction of this titanium foam sheet supports cutting, welding, and basic machining for assembly integration. The source explicitly states that the material can be machined, cut, and welded. However, the porous surface should be protected from crushing and contamination during handling. Custom dimensions are also available upon consultation.
What cleaning methods are recommended for the 30 µm sintered titanium foam sheet to maintain filtration performance?
The sheet can be cleaned using backflushing, steam, ultrasonic, or compatible chemical procedures, depending on the process medium and operating procedure. The source advises protecting the porous surface from crushing and contamination. These methods allow reuse without damaging the interconnected porous structure.
This sintered porous titanium foam sheet (30 µm filtration rating, 80 PPI, 160 × 160 × 10 mm) offers a corrosion-resistant, cleanable metallic filter medium with interconnected porosity (35–45%) and low flow resistance, suitable for solid-liquid and gas separation in laboratory and pilot-scale assemblies, though its 300°C service temperature limit and sensitivity to surface contamination require careful process matching.
Positive
- Corrosion-resistant titanium construction: The titanium-based porous structure provides corrosion resistance and thermal stability in compatible media, enabling use in aggressive chemical, petrochemical, and seawater environments without rapid degradation.
- Cleanable and reusable metallic filter: The metallic construction supports backflushing, steam, ultrasonic, and chemical cleaning procedures, allowing repeated use and reduced consumable waste compared to disposable filter media.
Trade-offs
- Limited service temperature ≤300°C: The recommended maximum service temperature of 300°C restricts application in high-temperature gas filtration or thermal processes exceeding this threshold, requiring alternative materials for elevated thermal conditions.
- Surface contamination vulnerability: The porous surface must be protected from crushing and contamination during handling and installation, as physical damage or particulate clogging can compromise filtration precision and flow uniformity.
Every advanced material, component, equipment, and instrument in our catalog is backed by rigorous testing. We maintain strict internal quality management frameworks and align with CE conformity metrics to deliver transparent, reproducible performance data via our public open-science repository.
To request raw batch performance data, submit formal vendor registration paperwork, or execute a fast-turnaround R&D manufacturing loop, contact us at inquiry@atomfair.com.
Item is dispatched under the Atomfair Shipping & Delivery Framework (Free worldwide shipping on orders over $59 USD excl. heavy equipment). Return is governed by the Atomfair Return & Refund Policy (7-day technical return window).
