|
Sintered Titanium and Porous Titanium Foam Sheet, 30 µm Filtration Rating, 100 × 200 × 3 mm, 20 PPI, 1 Piece
Research-grade laboratory product
|
|||||||||||||||||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||||||||||||||||
|
LABORATORY PROCUREMENT SUPPORT
For filtration accuracy, dimensional confirmation, material compatibility or custom configuration review, contact our technical sales team.
E-MAIL: inquiry@atomfair.com
|
|||||||||||||||||||||||||||||||||||||||||||||||
|
Manufacturer: Atomfair LLC
Brand: ATOMFAIR®
|
The porous titanium surface is susceptible to crushing and contamination, requiring protection during handling and storage. Recommended service temperature does not exceed 300°C, and media compatibility must be verified before installation.
- Surface Protection: Protect the porous surface from crushing and contamination to maintain filtration integrity.
- Temperature Limit: Do not exceed the recommended service temperature of 300°C to avoid structural degradation.
- Media Compatibility: Confirm media compatibility, operating pressure, and temperature before installation to prevent corrosion or failure.
Handle the sheet with care to avoid damaging the porous structure. Clean using backflushing, steam, ultrasonic, or compatible chemical methods based on the process medium.
Required Equipment: Backflushing system, Steam cleaner, Ultrasonic bath
- Inspect the sheet
Inspect the sheet for any visible damage or contamination before handling. - Select cleaning method
Select a cleaning method—backflushing, steam, ultrasonic, or chemical—based on the process medium and operating procedure. - Apply cleaning procedure
Apply the chosen cleaning procedure according to manufacturer guidelines to remove fouling without damaging the porous structure. - Rinse and dry
Rinse the sheet with compatible solvent or deionized water and allow it to dry completely before reuse.
How do the 30 µm filtration rating and 20 PPI pore density relate to each other in this sintered titanium foam sheet?
The 30 µm filtration rating and 20 PPI pore density are independent parameters. The 20 PPI (pores per inch) defines the cellular structure with approximately 1.27 mm cell spacing and 35–45% porosity, while the 30 µm rating specifies the particle retention size. Selecting both values together ensures the sheet provides both the desired flow path geometry and filtration precision for the application.
What is the maximum recommended service temperature for this sintered titanium foam sheet, and are there pressure limitations?
The recommended service temperature is ≤300°C based on the titanium material's thermal stability. The product description does not specify an absolute pressure rating, as operating pressure depends on the specific assembly, media compatibility, and dimensional tolerance; users should review these factors before installation.
What cleaning and handling procedures are recommended for this porous titanium foam sheet to maintain its filtration performance?
The sheet can be cleaned by backflushing, steam, ultrasonic, or compatible chemical procedures depending on the process medium. Handling should protect the porous surface from crushing and contamination to preserve the interconnected pore structure and filtration integrity.
This 3 mm sintered porous titanium foam sheet combines a 30 µm filtration rating with a 20 PPI cellular structure, 35–45% interconnected porosity, ~1.27 mm cell spacing, and 5×10^-4 L/(cm²·min·Pa) relative air permeability. It suits liquid/gas separation and flow-distribution trials within a 100 × 200 mm envelope, but media compatibility, operating conditions, and the crush-sensitive porous surface must be reviewed before installation.
Positive
- Sintered titanium with interconnected porosity: The high-vacuum sintered titanium structure provides 35–45% interconnected porosity with ~1.27 mm cell spacing, yielding low flow resistance and a 5×10^-4 L/(cm²·min·Pa) relative air permeability for liquid and gas flow.
- Cleanable and machinable metallic media: The titanium-based porous sheet can be cleaned by backflushing, steam, ultrasonic, or compatible chemical methods, and its metallic construction permits cutting, welding, and basic machining for integration into filtration assemblies.
Trade-offs
- Service temperature limited to 300°C: Recommended service temperature is ≤300°C, so the sheet should not be used in filtration or thermal processes operating above this threshold.
- Porous surface requires careful handling: The porous surface must be protected from crushing and contamination, and the cleaning method should be selected according to the process medium and operating procedure.
Every advanced material, component, equipment, and instrument in our catalog is backed by rigorous testing. We maintain strict internal quality management frameworks and align with CE conformity metrics to deliver transparent, reproducible performance data via our public open-science repository.
To request raw batch performance data, submit formal vendor registration paperwork, or execute a fast-turnaround R&D manufacturing loop, contact us at inquiry@atomfair.com.
Item is dispatched under the Atomfair Shipping & Delivery Framework (Free worldwide shipping on orders over $59 USD excl. heavy equipment). Return is governed by the Atomfair Return & Refund Policy (7-day technical return window).
