ATOMFAIR® HANDHELD COIN CELL ELECTRODE PUNCHRESEARCH GRADE MATERIAL
|
|||||||||||||||||||||||
|
|||||||||||||||||||||||
|
TAILORED SOLUTIONS FOR RESEARCH
Contact our engineering team for technical support or official quotations.
EMAIL: inquiry@atomfair.com
|
|||||||||||||||||||||||
|
Manufacturer: Atomfair LLC
Brand: ATOMFAIR®
|
This tool must be stored in a clean, dry atmosphere to prevent corrosion of the precision die edges. Regular lubrication of mechanical joints is required to maintain cutting accuracy and extend service life.
- Storage Environment: Keep the punch in a low-humidity, dust-free environment when idle to shield the die edges from rust.
- Lubrication Requirement: Periodically apply lubricant to the mechanical pivot points as specified in the manufacturer guidelines.
- Material Thickness Limit: Do not attempt to punch extra-thick or hard metal sheets that exceed the tool's rated capacity to preserve edge sharpness.
This procedure covers the manual operation of the punch for cutting electrode discs from foils and thin separators. Follow these steps to ensure reproducible disc geometry and avoid damage to the cutting edges.
Required Equipment: ATOMFAIR Handheld Coin Cell Electrode Punch
- Inspect the Punch
Inspect the die edges and mechanical joints for cleanliness and adequate lubrication before each use. - Position the Material
Place the electrode foil or separator on a clean, flat, non-slip surface to ensure even cutting. - Align the Punch
Align the punch die perpendicularly over the desired cutting area to avoid skewed disc edges. - Execute the Cut
Press the ergonomic handle firmly and steadily to punch the electrode disc with a single motion. - Post-Cut Handling
Remove the punched disc and immediately store the punch in a dry environment to prevent moisture damage.
Does the ultra-portable 0.3 kg design of the Atomfair electrode punch compromise punching force consistency across high-throughput electrode fabrication runs?
No, the ergonomic linear handle with tactical grip geometry dampens hand strain and yields highly uniform punching pressures across manual processing cycles, despite the lightweight 0.3 kg form factor. The high-strength die steel matrix ensures burr-free precision alignment and extended lifespan.
What are the maximum material thickness and hardness limits for the Atomfair handheld coin cell electrode punch when cutting coated cathode foils?
The tool is designed for standard lithium battery electrode sheets, metal foils, and thin separators typically used in CR2032/CR2025 coin cell assembly. The manufacturer explicitly warns against punching extra-thick or hard metal sheets exceeding tool capacity ratings, though specific thickness and hardness thresholds are not published. Users should limit usage to materials consistent with typical lithium-ion electrode fabrication.
What specific environmental and lubrication conditions are required to maintain the cutting edge integrity of the Atomfair handheld electrode punch during glovebox operations?
The punch must be stored in a clean, dry room environment when idle to prevent atmospheric humidity from corroding the die edges. Periodic verification of mechanical lubrication points according to original parameters is required. The unit ships in a specialized transit case to protect alignment, and its compact 0.3 kg design facilitates easy transfer between glovebox airlocks without contamination risk.
This handheld coin cell electrode punch offers precision cutting with interchangeable die diameters from 10mm to 20mm, suitable for lithium battery electrodes and separators, but requires controlled storage and periodic maintenance.
Positive
- High-strength die steel core: Fabricated from structural-grade die steel to extend lifespan and maintain cutting edge keenness over high-frequency cycle arrays.
- Burr-free precision alignment: Engineered tolerances guarantee accurate, debris-free disc boundaries, limiting baseline configuration errors during delicate coin cell stacking steps.
Trade-offs
- Environmental humidity sensitivity: The device must be housed in a clean, dry room when idle to protect critical die edges from atmospheric humidity and rust development.
- Limited material thickness capacity: Extra-thick or hard metal sheets exceeding tool capacity ratings cannot be punched, and periodic mechanical lubrication is required to maintain performance.
Every advanced material, component, equipment, and instrument in our catalog is backed by rigorous testing. We maintain strict internal quality management frameworks and align with CE conformity metrics to deliver transparent, reproducible performance data via our public open-science repository.
To request raw batch performance data, submit formal vendor registration paperwork, or execute a fast-turnaround R&D manufacturing loop, contact us at inquiry@atomfair.com.
Item is dispatched under the Atomfair Shipping & Delivery Framework (Free worldwide shipping on orders over $59 USD excl. heavy equipment). Return is governed by the Atomfair Return & Refund Policy (7-day technical return window).
