|
316L Stainless Steel Powder-Sintered Filter Plate, 10 µm Filtration Rating, Ø50 × 5 mm, 110 PPI, 1/5/10 pcs
Research-grade laboratory product
|
|||||||||||||||||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||||||||||||||||
|
LABORATORY PROCUREMENT SUPPORT
For filtration-grade selection, dimensional confirmation, material compatibility or custom configuration review, contact our technical sales team.
E-MAIL: inquiry@atomfair.com
|
|||||||||||||||||||||||||||||||||||||||||||||||
|
Manufacturer: Atomfair LLC
Brand: ATOMFAIR®
|
This document defines the operational limits and maintenance requirements for the 316L stainless steel powder-sintered filter plate. Adherence to these constraints prevents damage and ensures consistent filtration performance.
- Temperature Limit: Limit normal use temperature to 500 °C maximum.
- Pressure Handling: Increase working pressure gradually up to a maximum of 3 MPa to avoid structural stress.
- Cleaning Compatibility: Use only compatible cleaning methods such as backblowing, backwashing, ultrasonic cleaning, or approved chemical agents.
- Surface Integrity: Avoid impact, scratching, or concentrated tool pressure on the porous surface to prevent damage.
- Efficiency Monitoring: If filtration efficiency falls below 50%, perform a validated cleaning procedure before further use.
These steps guide the installation, pressure ramp-up, and cleaning of the sintered filter plate to maintain performance. Following this procedure ensures safe operation and extends the product's service life.
Required Equipment: Filter housing with compatible fittings, Pressure regulation valve, Backwashing or backblowing system, Ultrasonic cleaner (optional)
- Verify Specifications
Confirm the filter plate's dimensions, filtration rating, and material compatibility with the intended process medium. - Install the Plate
Place the filter plate into the housing with the flow direction from the outside surface toward the clean side. - Gradually Increase Pressure
Slowly raise the working pressure up to the maximum 3 MPa while monitoring the differential pressure and flow rate. - Monitor Filtration Efficiency
Check the filtration performance regularly and if efficiency drops below 50%, prepare for cleaning. - Perform Backwashing or Backblowing
Apply a clean fluid or gas stream in the reverse direction to dislodge retained particles. - Implement Chemical Cleaning if Needed
Select a compatible chemical agent based on the retained material and process medium, then rinse thoroughly with clean fluid. - Verify Performance After Cleaning
Reinstall the cleaned plate and test flow and filtration efficiency before resuming full operation.
What is the maximum working pressure and temperature for the 316L powder-sintered filter plate with 10 µm rating and 110 PPI structure?
The filter plate has a normal use temperature of ≤500 °C and a maximum working pressure of ≤3 MPa. These limits apply to the Ø50 × 5 mm, 110 PPI, 10 µm filtration-rated 316L stainless steel powder-sintered plate, as stated in the technical specifications.
Can this 316L sintered filter plate be cleaned and reused, and what cleaning methods are compatible?
Yes, the powder-sintered metallic media can be regenerated by compatible backblowing, backwashing, ultrasonic cleaning, or chemical cleaning using dilute acid, dilute alkali, oxidizing agents, surfactants, or enzymes. The cleaning method should be selected based on the retained material and process medium, and surface damage, rapid pressurization, and incompatible chemicals should be avoided.
What are the key dimensional and structural parameters of the 110 PPI porous structure in this filter plate?
The 110 PPI porous structure has a nominal pore spacing of 0.23 mm, porosity of 30–45%, and bulk density of 4.4–5.6 g/cm³. The plate diameter is Ø50 mm with a thickness of 5 mm, and the material is 316L stainless steel powder with a density of 8.0 g/cm³.
This 316L stainless steel powder-sintered filter plate offers 10 µm filtration with a 110 PPI porous structure, providing uniform pore distribution and low initial resistance for gas or liquid filtration. Its cleanable, self-supporting design enables repeated use under controlled operating conditions up to 500 °C and 3 MPa.
Positive
- Uniform pore structure and low resistance: The 110 PPI porous structure with 0.23 mm nominal pore spacing and 30–45% porosity provides stable gas or liquid passage with low initial resistance across the Ø50 × 5 mm disc.
- Multiple regeneration methods: The powder-sintered 316L construction can be cleaned by backblowing, backwashing, ultrasonic cleaning, or compatible chemical procedures, enabling repeated use when surface damage is avoided.
Trade-offs
- Requires gradual pressure increase: Pressure must be increased gradually, and if filtration efficiency falls below 50%, a validated backblowing or backwashing procedure is required. Impact, scratching, or concentrated tool pressure on the porous surface must be avoided.
- Operating limits on temperature and pressure: Normal use temperature is limited to ≤500 °C and maximum working pressure to ≤3 MPa; operating outside these ranges may compromise performance or structural integrity.
Every advanced material, component, equipment, and instrument in our catalog is backed by rigorous testing. We maintain strict internal quality management frameworks and align with CE conformity metrics to deliver transparent, reproducible performance data via our public open-science repository.
To request raw batch performance data, submit formal vendor registration paperwork, or execute a fast-turnaround R&D manufacturing loop, contact us at inquiry@atomfair.com.
Item is dispatched under the Atomfair Shipping & Delivery Framework (Free worldwide shipping on orders over $59 USD excl. heavy equipment). Return is governed by the Atomfair Return & Refund Policy (7-day technical return window).
