|
Indium(II) Telluride (InTe) Evaporation Material, Powder, 99.9%, 35 µm
Product Type: Compound Evaporation Material
Research-grade laboratory product
|
|||||||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||||||
|
LABORATORY PROCUREMENT SUPPORT
For material selection, deposition-source matching, pack-size confirmation or quotation support, contact our technical sales team.
INQUIRY: inquiry@atomfair.com
|
|||||||||||||||||||||||||||||||||||||
|
Manufacturer: Atomfair LLC
Brand: ATOMFAIR®
|
This evaporation material requires matched deposition source hardware and controlled thermal conditions. Particle size, purity, and crucible type must be verified before loading to prevent contamination or incomplete evaporation.
- Particle Size and Form: The powder is supplied at 35 µm particle size; use consistent particle size to ensure uniform evaporation rate.
- Crucible Compatibility: Use quartz, alumina, graphite crucibles, Ta/W boats, or Knudsen cells; verify compatibility with material melting point and vapor pressure.
- Evaporation Method: Thermal evaporation or low-power e-beam is recommended; confirm source geometry and power limits.
- Melting Point Consideration: The material melting point is 696°C; ensure the deposition system can reach and maintain this temperature.
- Pre-Use Verification: Confirm purity (99.9%), form, and pack size before loading to avoid process deviation.
This procedure guides the safe handling and deposition of InTe powder in a vacuum evaporation system. Verify hardware compatibility and material specifications before loading.
Required Equipment: Thermal evaporator, Crucible (quartz, alumina, or graphite), Tantalum or tungsten boat, Knudsen cell
- Verify Hardware Compatibility
Confirm the deposition source hardware, such as crucible, boat, or Knudsen cell, is compatible with InTe powder and the evaporation method. - Inspect Material Specifications
Inspect the powder purity, particle size, and pack size to ensure they match the process requirements. - Set Evaporation Parameters
Set the evaporation temperature based on the material melting point of 696°C and optimize process parameters for the target film.
What is the significance of the 35 µm particle size for Indium(II) Telluride (InTe) evaporation material?
The 35 µm powder form is specified to support source loading and controlled evaporation during vacuum thin-film deposition. The fine particle size increases surface area, which can influence outgassing rates and thermal conductivity during heating, and aids in uniform loading into crucibles or boats. Users should confirm compatibility with their deposition source geometry before ordering.
Which evaporation source hardware is compatible with InTe powder for thin-film deposition?
InTe powder can be used with thermal evaporation or low-power e-beam deposition by RFQ. Recommended crucible materials include quartz, alumina, or graphite, and boats can be tantalum or tungsten. A Knudsen cell is also an option by RFQ. The exact hardware should be matched to the material's melting point (696) and density (6.29) to ensure proper evaporation and film quality.
What documentation and procurement checks are required before ordering InTe evaporation material?
Before ordering, confirm the model (AF-INTEPWD-3N35UM), purity (99.9%), form (powder), particle size (35 µm), and pack size (25g, 100g, 500g, or 1kg). Review the certificate of analysis, safety data sheet, shipment conditions, and export requirements for laboratory use. Ensure the deposition source hardware is compatible with the material's thermal behavior and process route.
Indium(II) Telluride (InTe) evaporation material supplied as 99.9% pure powder with 35 µm particle size, suitable for thermal evaporation or low-power e-beam deposition. Requires careful matching of crucible/boat hardware and process parameters to the material's melting point (696°C) and density (6.29 g/cm³).
Positive
- Defined material identity and purity: Indium(II) Telluride (InTe) with 99.9% purity and 35 µm powder form ensures clear procurement matching and deposition process control.
- Specified physical form and particle size: Powder with 35 µm particle size facilitates consistent source loading and evaporation behavior in vacuum deposition.
Trade-offs
- Deposition source compatibility required: Buyers must verify crucible/boat type (quartz, alumina, graphite, Ta/W, or Knudsen cell) and deposition geometry before ordering to ensure hardware compatibility.
- Process parameter matching necessary: Evaporation source hardware and process route must be matched to the material's melting point (696°C) and density (6.29 g/cm³) to achieve desired film properties.
Every advanced material, component, equipment, and instrument in our catalog is backed by rigorous testing. We maintain strict internal quality management frameworks and align with CE conformity metrics to deliver transparent, reproducible performance data via our public open-science repository.
To request raw batch performance data, submit formal vendor registration paperwork, or execute a fast-turnaround R&D manufacturing loop, contact us at inquiry@atomfair.com.
Item is dispatched under the Atomfair Shipping & Delivery Framework (Free worldwide shipping on orders over $59 USD excl. heavy equipment). Return is governed by the Atomfair Return & Refund Policy (7-day technical return window).
