Description
HM100-Pro Heating Shaking Dry BathProduct Type: Temperature control instrument
Research-grade temperature control platform
|
|||||||||||||||||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||||||||||||||||
|
TAILORED SOLUTIONS FOR RESEARCH
For bulk orders, OEM requirements, accessory matching or configuration confirmation, contact our engineering sales team.
EMAIL: inquiry@atomfair.com
|
|||||||||||||||||||||||||||||||||||||||||||||||
|
Supplier: Atomfair
Brand: ATOMFAIR®
|
This document outlines operational constraints and safety limits for the HM100-Pro Heating Shaking Dry Bath. Compliance with these constraints ensures safe and reliable operation of the instrument.
- Electrical Supply Requirements: Operate the unit only with the specified power supply of 110/220 V, 50/60 Hz to prevent electrical damage or hazard.
- Ambient Environment Limits: Maintain ambient temperature between 10 and 40 °C and relative humidity below 80% to avoid condensation and overheating.
- Thermal Safety Precautions: Never touch the heating block or sample vessels during or immediately after operation, as surface temperatures can exceed 100 °C.
- Block Compatibility Warning: Use only confirmed compatible heating blocks or modules to ensure proper fit and uniform heat transfer.
- Overload Prevention: Do not exceed the maximum sample load or block weight specified for the shaking mechanism to avoid mechanical failure.
Follow these steps to correctly set up and operate the HM100-Pro Heating Shaking Dry Bath. These actions ensure safe handling and accurate temperature control during sample incubation.
Required Equipment: Compatible heating block or module, Sample vessels (tubes, vials, or plates)
- Verify Power Supply
Confirm that the mains power matches the unit's nameplate rating (110/220 V, 50/60 Hz) and plug into a grounded outlet. - Install Compatible Heating Block
Select a heating block or module that accommodates your sample vessel format and securely insert it into the dry bath. - Set Temperature and Timer
Use the TFT interface to program the desired temperature (0 to 100 °C) and timer duration (0 min to 99 h 59 min). - Load Samples
Place sample vessels into the heating block, ensuring they are properly seated and balanced to prevent spillage. - Start Shaking and Heating
Initiate the shaking function at the required speed (200 to 1500 rpm) and allow the block to reach the set temperature. - Monitor Operation
Observe the TFT display for actual temperature and timer progress; adjust parameters only when the unit is not in active heating mode. - Power Off and Cool Down
After the timer expires, stop shaking, power off the unit, and allow the heating block to cool below 40 °C before handling.
How does the maximum heating rate of 5.5°C/min affect temperature control accuracy for sensitive enzymatic reactions on the HM100-Pro?
The HM100-Pro maintains a temperature control accuracy of ±0.5°C at steady state despite a maximum heating rate of 5.5°C/min. For highly temperature-sensitive reactions, users should note that while the steady-state accuracy is specified, rapid ramp rates may require programmed slower ramps to minimize transient overshoot; the instrument supports custom program capacity of 9 programs with 150 process execution steps.
Which heating blocks or sample modules are compatible with the HM100-Pro heating shaking dry bath?
The product description does not list specific compatible blocks or modules; it explicitly advises confirming block or module compatibility, sample vessel format, and installation environment before ordering. Users must contact the Atomfair technical sales team (inquiry@atomfair.com) for method-specific incubation, heating, or module matching requirements.
What ambient temperature and humidity limits are required for reliable operation of the HM100-Pro dry bath?
The HM100-Pro requires an ambient temperature of 10 to 40°C and relative humidity below 80% for reliable operation. It accepts power supply of 110/220 V, 50/60 Hz and draws 200 W, making it suitable for standard laboratory bench environments within those limits.
The HM100-Pro Heating Shaking Dry Bath provides dry-block heating with orbital shaking for uniform sample incubation and mixing across a temperature range of ambient to 100°C, with ±0.5°C accuracy. Its operation requires selection of compatible heating blocks or modules, and lacks active cooling below ambient temperature.
Positive
- Integrated heating and orbital mixing: Combines dry-block heating with orbital shaking (200–1500 rpm, 3 mm orbit) for simultaneous incubation and mixing in a single instrument, reducing workflow steps and contamination risk.
- Programmable timed operation: Supports up to 9 custom programs and 150 process execution steps with a timer range of 0 min to 99 h 59 min, enabling automated, reproducible protocols for extended or multi-step sample preparation.
Trade-offs
- Block compatibility must be user-verified: The unit requires separately selected heating blocks or modules matched to the specific sample vessel format; failure to confirm compatibility before ordering can delay deployment or cause operational mismatch.
- No active cooling below ambient: Temperature control is limited to heating from room temperature up to 100°C; the instrument cannot cool below ambient, restricting its use for cold incubation or low-temperature reactions without external cooling.
Every advanced material, component, equipment, and instrument in our catalog is backed by rigorous testing. We maintain strict internal quality management frameworks and align with CE conformity metrics to deliver transparent, reproducible performance data via our public open-science repository.
To request raw batch performance data, submit formal vendor registration paperwork, or execute a fast-turnaround R&D manufacturing loop, contact us at inquiry@atomfair.com.
Item is dispatched under the Atomfair Shipping & Delivery Framework (Free worldwide shipping on orders over $59 USD). Return is governed by the Atomfair Return & Refund Policy (7-day technical return window).
