Description
ATOMFAIR® EB320G-0.1MG-01 ELECTRONIC ANALYTICAL BALANCERESEARCH GRADE METROLOGY
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
TAILORED METROLOGY FOR RESEARCH
Contact our engineering team for technical support or official institutional quotations.
EMAIL: inquiry@atomfair.com
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Manufacturer: Atomfair LLC
Brand: ATOMFAIR®
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
This precision balance requires a regulated thermal environment (18–23°C) and non-condensing humidity (20–80%RH) to maintain 0.1 mg readability. An initial warm-up of 30–60 minutes is mandatory for sensor stabilization, and auto-calibration is triggered by thermal fluctuations exceeding 1.5°C or every two hours.
- Environmental Temperature: Maintain ambient temperature within 18–23°C, as deviations beyond this range degrade measurement accuracy.
- Atmospheric Humidity: Keep relative humidity between 20% and 80% non-condensing to avoid condensation on internal components.
- Warm-up Duration: Allow the balance to power on and stabilize for 30–60 minutes before performing any critical measurements.
- Vibration Isolation: Place the balance on a stable, vibration-free surface; the split-display design reduces but does not eliminate kinetic interference.
- Auto-Calibration Triggers: The balance automatically recalibrates when internal temperature changes >1.5°C or after two hours of continuous operation.
Follow these steps to achieve 0.1 mg precision with the analytical balance. Proper warm-up and environmental control are critical for reliable metrology.
Required Equipment: 12V/2A power adapter (provided)
- Connect Power
Connect the balance to a 220VAC/50Hz mains supply using the provided 12V/2A power adapter. - Position the Balance
Place the balance on a rigid, level surface away from drafts, vibrations, and direct sunlight. - Perform Warm-up
Allow the balance to warm up for 30–60 minutes to stabilize the electromagnetic sensor. - Verify Environment
Confirm that ambient temperature is 18–23°C and relative humidity is 20–80% using a separate monitor. - Execute Calibration
Trigger auto-calibration via the menu or wait for automatic recalibration upon temperature change or time lapse. - Tare and Weigh
Tare the pan with an empty container, then place the sample and record the stable reading.
What is the trade-off between maximum capacity and readability in the EB220G-0.1MG-I-02 analytical balance?
The EB220G-0.1MG-I-02 offers 0.1mg readability (d) with a maximum capacity of 320g, which is a high capacity for a 0.1mg readability balance. The repeatability error is ±0.1mg and linearity error is ±0.2mg, ensuring precision across the full range. This balance is optimized for ultra-low mass powder and fluid tracking up to 320g, but users must allow 30–60 min warm-up and operate within 18–23°C to maintain that performance.
Can the EB220G-0.1MG-I-02 be integrated with a Laboratory Information Management System (LIMS) or external PC?
Yes, it is equipped with an industrial RS232 communication interface for bidirectional data synchronicity, allowing seamless integration with peripherals, PCs, and third-party LIMS environments. This enables direct data transfer without manual recording, reducing transcription errors.
What are the power and environmental requirements for operating the EB220G-0.1MG-I-02 at its rated accuracy?
The balance requires a power input of 220VAC 50Hz, with an output of 12V/2A DC. It must be operated in a regulated thermal zone of 18°C–23°C and non-condensing humidity of 20%–80%RH. An initial warm-up of 30–60 minutes is necessary before verification to achieve 0.1mg repeatability.
The ATOMFAIR EB220G-0.1MG-I-02 analytical balance offers 0.1mg readability with a 320g capacity, leveraging a rear-mounted electromagnetic sensor and vibration-isolated split design for reliable micro-powder and fluid measurements, but requires a controlled environment and 30-60 minute warm-up for optimal accuracy.
Positive
- Rear-mounted electromagnetic force restoration: Provides ultra-responsive, rapid, and drift-free mass detection for high-precision measurements.
- Vibration-isolated split design: Decouples the LED display from the weighing mechanism to eliminate keystroke kinetic interference.
Trade-offs
- Extended warm-up requirement: Requires 30-60 minute warm-up and internal calibration within 18-23°C to achieve specified 0.1mg metrology.
- Controlled thermal environment needed: Operating ambient temperature must be tightly regulated between 18°C and 23°C; deviations may affect performance.
Every advanced material, component, equipment, and instrument in our catalog is backed by rigorous testing. We maintain strict internal quality management frameworks and align with CE conformity metrics to deliver transparent, reproducible performance data via our public open-science repository.
To request raw batch performance data, submit formal vendor registration paperwork, or execute a fast-turnaround R&D manufacturing loop, contact us at inquiry@atomfair.com.
Item is dispatched under the Atomfair Shipping & Delivery Framework (Free worldwide shipping on orders over $59 USD). Return is governed by the Atomfair Return & Refund Policy (7-day technical return window).
